How to transfer a design from paper to paper and other surfaces

2024 Author: Leah Sherlock | [email protected]. Last modified: 2023-12-17 05:25

If you don't know how to draw, but would like to learn, you should start with a simple one - copying drawings. To begin with, this can be done with the help of tracing paper. This method is the easiest to perform. Now let's learn more precisely how to transfer a drawing from paper to paper.

Instructions

To transfer an image, follow the steps below:

1. Select the image and, putting tracing paper on it, circle all the lines with firm pressure, using a black acrylic pen.
2. Now turn the tracing paper over and put it face down on the sheet of paper on which you want to transfer the image.
3. Press firmly and pass over it with a hot iron.
4. Now remove the tracing paper and additionally draw insufficiently clear lines.
5. Image done.

This method is used for simple pictures that do not contain a lot of complex details. Now you know how to transfer a drawing from paper to paper.in a simple way. After trying it, you can proceed to others.

The more difficult way

To transfer complex patterns, you can use the copy grid. With its help, it is also possible to reduce or increase the scale of the image itself.

Needed:

• original picture;
• transparent film;
• capillary pen;
• paper;
• adhesive tape;
• ruler;
• pencil.

Instructions

To master this method, follow these steps:

1. We apply a transparent film on the original image, which shows squares of the same size.
2. We put the same cell on a blank sheet of paper if the picture is reproduced in the original. How to transfer a drawing from paper to paper when the image needs to be resized? When increasing the size of the squares, they make more, when we decrease, respectively, less.
3. Now all you have to do is move the image over the cells.
4. When the picture is completely transferred with a pencil, you can start decorating.

Now you know how to transfer an image from paper to paper. Consider other surfaces.

The body as a foundation

A tattoo is a highlight of appearance, but not everyone decides to put a drawing on the skin, realizing that this decision is made for life. For people who are afraid of such an act, howeverwant to decorate their body with a beautiful image, temporary tattoos are an excellent solution. To learn how to transfer a design from paper to leather, you need to study the following information. The main stage is a clear drawing of the contours of the future image.

The picture can be applied to the body with:

• carbon paper;
• tracing paper.

First way

For him you need to do the following:

1. Choosing a pattern, determining the place of its application, disinfecting the skin.
2. Transferring an image to carbon paper. To do this, put the paper on the original and carefully outline all its contours.
3. Wet carbon paper with alcohol and apply to the body.
4. For the contours to print well, circle them again through the carbon paper, trying to leave it intact.

Second way

It is based on the use of tracing paper. You need to do the following steps:

1. We draw the drawing itself with a helium pen.
2. Disinfect the skin and smear with soap.
3. Apply tracing paper and outline the contours with a sharp object.
4. Now paint over the drawing.

If you still decide to put a permanent drawing on your body, approach this very carefully. The main thing is to choose a good salon, get tested for an allergic reaction and make sure that all tools are disinfected.

How to transfer a design from paper to glass

To work, we take an image with good contours and a roll of cling film. To transfer, you need to purchase a felt-tip pen - a marker for glass, it fits well and is easily washed offfrom the surface.

Instruction:

1. We take the film. Its size should be slightly larger than the drawing itself. The film is attached to the surface, which prevents the picture from going astray.
2. The image is placed on film and outlined thinly and very carefully.
3. Now the film is gently transferred face down to the previously prepared surface. Preparation consists in degreasing its front side. Make sure the film is fully adhered to the glass, get rid of wrinkles and bubbles.
4. For a clearer transfer, we circle the image with any sharp object again along the contour.
5. It's time to get rid of polyethylene. We do this very carefully so as not to smear the drawing. If there are inaccuracies somewhere, now is the time to correct them.
6. Now draw the outline. This can be done with acrylic paints and a brush.
7. After everything is dry, carefully use cotton swabs dipped in liquid to get rid of traces of the marker.
8. Inside the image is filled in any way. If the technique is stained glass, then everything is poured along the contour.
9. After drying, for a longer service life of the product, the image can be baked or varnished. It all depends on where this item will be used.

How to transfer a drawing from paper to wood

To see your favorite wooden base image, just follow the steps below.

For workrequired:

• drawing printed on a laser printer;
• wooden board;
• acrylic gel medium;
• flat pattern leveling tool;
• paint and rag;
• soft wax or matte glue;
• 2 brushes.

Instruction:

1. Select image. It should be a drawing that will look nice on a wooden base. To give some resemblance to the vintage style, it can be processed in special programs.
2. The image is printed only on a laser printer, this is the main condition.
3. Smooth wood base selected.
4. Now apply an even layer of the gel medium. It is he who will help the image to transfer to the prepared surface.
5. We place the pattern with the front side to the base. At the moment of connection, bubbles appear, which should be smoothed out if possible.
6. Work done for today, leave everything overnight, continue tomorrow.
7. It's time to remove the paper. To do this, wet it and rub it with your fingers. Right now you are witnessing a miracle - when you remove the paper, you can see how the image remains on the tree.
8. Wood paint can now be used. Keep an eye on its amount so that the image does not darken.
9. Now apply liquid paraffin. If necessary, the last two steps can be repeated after the first coat has dried.

Other basics for image transfer

Metal is the basis, also suitable for such "tricks". For neat andenough accurate work on it draw two axial lines or mark the corners of the image. Now let's take a closer look at how to transfer a drawing from paper to metal.

The most common is to use carbon paper for this. Since metal is a very hard material, it is coated with white or light paint. The transfer process begins after the varnish has completely dried, which is applied just before the start of the main work.

Instructions

This method requires the following rules:

1. The pattern is very tightly fixed on the product. You can use soapy water for this.
2. Many craftsmen use chasing-kanfarnik for this work. With it, the image is very accurate - almost a jeweler's work, which, however, takes a very long time and requires some preliminary training.
3. The tool is taken with three fingers, resting on the ring finger, which serves as a kind of spring. The coinage is located 2-3 mm from the drawing, its light strokes form a dotted line - the main outline of the image is drawn. The smaller the detail of the picture, the denser it breaks through.
4. When all the lines are transferred, you can wash off the paint.
5. Image can be varnished.

Now you know how to transfer a design from paper to paper, leather, glass, wood and metal. Forward - for the tools, and good luck in your endeavors!